Bosco Label CSQ set (2 Viewers)

[louBdub]

Wanted to share this little label journey with y’all.

I bought some CSQ solids from @GenghisKhan to mill up. For what, I didn’t know, but I knew they would be a fun project.

So, after milling and playing with label options, I decided to go with the simple/clean Bosco ACES label. I found @dickthebaker on here and wanted to give him a try.

So, without further yappin, here’s my labeling project thread.

MORE TO FOLLOW!

 

[louBdub]

Micro set, with a high side snapper, because it’s my set, and I wanted to get weird with it

 

[timinater]

Damn look at the carnage! Great job. I wonder if Dewalt makes something to clean that up?

 

[louBdub]

Damn look at the carnage! Great job. I wonder if Dewalt makes something to clean that up?

Haha, I had my shop vac propped to the side to keep it kinda clean, but as Ive made plenty of messes in the shop before, I usually decide to just go wild, and then clean up after.

Same as the sex approach

 

[Colquhoun]

Nice mill setup. Those recesses look a bit deep, are you using a thick laminate label?

 

[louBdub]

Nice mill setup. Those recesses look a bit deep, are you using a thick laminate label?

Yeah it’s my first time, might have gone a tad deep, but it’ll buff out. Textured labels going in though.

I literally read a few threads on here, ordered the bit from @Eloe2000 ‘s thread, and went to town. My biggest concern was accuracy with 1” cut, on a CSQ. Off center milling tilts me to death more than depth.

 

[dickthebaker]

Wowwee thats a lot of clay. Labels likely getting started tomorrow afternoon. Thanks!

 

[allforcharity]

Oww that recess is really deep. Probably will get more precise with practice.

Consistent (appropriately shallow) recess depth is probably the only real advantage of using the bottom router method.

 

[lib]

do you run a dewalt dealership?

 

[louBdub]

Oww that recess is really deep. Probably will get more precise with practice.

Consistent (appropriately shallow) recess depth is probably the only real advantage of using the bottom router method.

It’ll be aight haha. If was fun doing it, and I’m excited to label them up and throw them around!

 

[louBdub]

do you run a dewalt dealership?

HA! I wish they’d just sponsor my life. I own just about everything a DIYer should own from them, next step is the full 60v line - just because MOAR POWA

 

[louBdub]

Sneak peek

 

[dickthebaker]

Sneak peek
View attachment 913047

The light spots on the labels have been taken care of and are no longer there

 

[GenghisKhan]

I've been trying to come up with custom names for years. I am a procrastinator. You sir, waste no time.

Good job on the milling and labels.
This will make a nice set.

 

[Kid_Eastwood]

Nice project !

 

[louBdub]

 

[louBdub]

 

[louBdub]

 

[louBdub]

All hand washed, milling dust rinsed and wiped…

READY FOR LABELS TOMORROW!!!

 

[louBdub]

Dear mr post man……….

 

[dickthebaker]

are they there yet, are they there yet? it could have been there 5 minutes ago. You may want to try placing them with your fingers before the tools, it will go much faster if you have steady enough hands. In my experience at least. also don't use that spudger to push down hard on the label, it just needs a little bit of pressure

 

[louBdub]

 

[dickthebaker]

 

[louBdub]

1 rack

I’m LOVING THEM!!!!!

Ok, back to work!!!

 

[dickthebaker]

Order #:0001 complete!

 

[louBdub]

Cookin now…..

 

[louBdub]

Home stretch…..

 

[louBdub]

I did it….. I’m gonna need a nap, but it’s done….

Proper pr0n later………. I’m taking a break

 

[louBdub]

 

[louBdub]

Juiced up…

Final wipe tomorrow, then pr0n