-
This site contains affiliate links. If you choose to make a purchase after clicking a link, Poker Chip Forum may receive a commission at no additional cost to you. Thank you for your support!
Sale Made-to-order Custom Table Toppers (62 Viewers)
- Thread starter rjdev7
- Start date
ItsAlwaysLupus
Sitting Out
I think this design is dope. The white is great but it would be too bright for my room. Basement florescent lighting bouncing off that all night lol.
Well you're looking at some oldie but goodie work there... Perhaps try a tropical tan and brown - my personal one
Or how about a new clean blue
ItsAlwaysLupus
Sitting Out
For sure. I was skimming through the whole thread. Decided I'm calling my home poker room 4 Kings, so was looking for something that would for that.
MeridianFC
Flush
PM sent
OP
OP
All of this info can be found in the original post in this thread, but in short, they're 2mm vs. 4mm in thickness. Print quality is as good or better than the PCF toppers (I used the same vendor as the PCF toppers for the Fall and Winter group buys that I ran). That being said, you should probably take everyone else's word for it by looking through this thread and reading through the testimonials. Happy to answer any other questions you have.
Venturalvn
Full House
Is there any review for how they handle cleaning/spills/liquid? Just curious is the right move to scotch guard it? Or just leave it be because it's just that bad ass.
OP
OP
I’ve had a few orders of max width since then that came out fine, but you’ll want to go without sewn edges if you go with a 48” round. The round toppers don’t seem to lay as flat with sewn edges based on feedback from folks.
ItsAlwaysLupus
Sitting Out
That purple and green could make for a sick Joker and/or Riddler theme.
Mike mac
4 of a Kind
finally figured out how to post this video here. the speed of this topper is sick , my dealer loves it and all my poker crew loved it too!
https://youtube.com/shorts/gKH-hfLDLVQ?feature=share
https://youtube.com/shorts/gKH-hfLDLVQ?feature=share
I'm always a huge art deco guy, so I've toyed around with the idea of a batman animated series one for a while, just a Gotham casino with that great lettering from the show, and a Gotham skyline one of the artists drew. And yes, it certainly made me think joker when I did it lol
https://www.pokerchipforum.com/threads/made-to-order-custom-table-toppers.96993/post-2100466
Also if you didn't see the one @Mike mac ordered, it also came out Sick.
Dude where's the video for that one?!
ItsAlwaysLupus
Sitting Out
Yeah it looks so great. I think that art deco lends itself well to like a cool batman noir type thing too. My artistic ability is less than 0 haha. I know what I like but sure can't do any of it.
ItsAlwaysLupus
Sitting Out
Brrrruuuceeeee waayyyyneeeee
Paulo
Flush
For those members who have cupholders on their poker table playing field and have hesitations or concerns about having to cut these beautiful toppers to allow for the cupholders; here are some photos of how my topper turned out.
You’ll see my original table and felt along with the new topper added. I think I’m gonna order another
Thanks again @rjdev7 and @aaron2786 for all the help. Also shout out to @Mike mac for referral. I think it turned out great.
You’ll see my original table and felt along with the new topper added. I think I’m gonna order another
Thanks again @rjdev7 and @aaron2786 for all the help. Also shout out to @Mike mac for referral. I think it turned out great.
Attachments
Last edited:
Riddler409
Pair
This looks great! Did you add any additional padding underneath?For those members who have cupholders on their poker table playing field and have hesitations or concerns about having to cut these beautiful toppers to allow for the cupholders; here are some photos of how my topper turned out.
You’ll see my original table and felt along with the new topper added. I think I’m gonna order another
Thanks again @rjdev7 and @aaron2786 for all the help. Also shout out to @Mike mac for referral. I think it turned out great.
Paulo
Flush
No. I just carefully cut the holes out using a sharp pair of scissors.
I started by removing the cupholders from the table, then laid out the topper. Marked the topper from underneath the table where the cupholder holes are using a white paint marker/fabric marker, then cut.
Cupholders have a slight rim around them so the topper laid fairly clean and flat.
I’m happy with the outcome.
Riddler409
Pair
I meant underneath the topper. Are you just using the 2mm padding that it has, or did you use an additional layer below?
Paulo
Flush
Didn’t use anything underneath
- Joined
- Nov 22, 2018
- Messages
- 13,721
- Reaction score
- 29,541
- Location
- 129 West 81st Street, Apartment 5B
From a distance, the racetrack already looks similar-ish to the shape of a tie fighter. I’d probably sneak one in just as an Easter egg.
Taxi500
3 of a Kind
I've looked through this thread a bit but can't find info on cleaning.
Are we able to clean these toppers? If so, how? Specifically, beer spills...
Are we able to clean these toppers? If so, how? Specifically, beer spills...
I cleaned my PCF with wetsuit cleaner; following the instructions in the bottle.
Has anyone worked on a rendering for a Terrible's Casino table topper yet? Would love to see some ideas and/or creations.
Riddler409
Pair
I love the background on that! It’s almost generic enough to stand on its own in various colors schemes!
Last edited:
Shhhh!!! I already own 6 toppers and if someone makes a Kings Crown or Terribles, those are must buys for me! No one needs 8 toppers, let alone 6 for 2 tables!
Create an account or login to comment
You must be a member in order to leave a comment
Create account
Create an account and join our community. It's easy!
Log in
Already have an account? Log in here.
Similar threads
