-
This site contains affiliate links. If you choose to make a purchase after clicking a link, Poker Chip Forum may receive a commission at no additional cost to you. Thank you for your support!
GB Completed China Chip Racks- January 2023 (1 Viewer)
- Thread starter justincarothers
- Start date
- Status
OP
OP
Will be going up this week
MichaelBubly
Flush
If there are any extra 43mm racks or if anyone ordered a few extra, looking for 4. Realized my CPCs don't fit the 39mm racks sadly.
If not I'll jump in the next one!
If not I'll jump in the next one!
FYI, you probably already know this, but your PGI 8Vs will only fit 19 to a barrel in these racks...
I have them slanting backwards in this pic so you can see there is just a tiny gap.
WHAT?!?!?!?! GB......
turboj623
Flush
Finally got around to opening my box and I have to admit. These racks are awesome. If you run another buy, I'm def buying a bunch more.
larch
Pair
@justincarothers What’s the best way to get notified about another group buy for these? Just follow you?
OP
OP
Yes. I will try to remember to tag you as well
Or put an alert for new threads on the group buy forum. You might be surprised at how few new threads actually pop up— shouldn’t be too annoying at all. That’s what I did to watch for this one.
ChrisTot
Pair
Which racks are the appropriate size for China Clay Pharaoh’s? I totally wanna be in on the next group buy! =)
Colquhoun
4 of a Kind
Suddenly, I could use 2-4 more 40mm of these racks, if anyone has some extras in their order that they can part with...
I could wait for the next one, but figured I'd reach out.
Thanks!
I could wait for the next one, but figured I'd reach out.
Thanks!
I wanted to throw this out there how these racks fit into cases. I got 1000 chips (43mm racks) into an Apache 3800. Fits nearly perfect with only a very slight wiggle, which is not noticeable. I have 600 43mm and 400 39mm chips, all CMs. Yeah, the 39mm chips wobble a bit, but I doesn't bother me.
I didn't use either of the middle foam pads = not having to buy a dozen bottles of plasti dip that cost more than the case itself nor did I have to pluck any foam. For now, I just put some styrofoam up front and notched out a place to grab the middle rack. I will see how I like this configuration and save the foam for later if I ever want to change it up. Easy enough to have 2 configurations since no foam is needed in one of them.
I don't care about being able to put cards, cut cards, buttons, etc in the case. Those are easy enough to carry separately. I always want to have a set up backup cards and 4 decks wouldn't fit.
Also, I read somewhere that after time foam can mess up the chips. Glad I don't have to worry about that with these enclosed racks.
I didn't use either of the middle foam pads = not having to buy a dozen bottles of plasti dip that cost more than the case itself nor did I have to pluck any foam. For now, I just put some styrofoam up front and notched out a place to grab the middle rack. I will see how I like this configuration and save the foam for later if I ever want to change it up. Easy enough to have 2 configurations since no foam is needed in one of them.
I don't care about being able to put cards, cut cards, buttons, etc in the case. Those are easy enough to carry separately. I always want to have a set up backup cards and 4 decks wouldn't fit.
Also, I read somewhere that after time foam can mess up the chips. Glad I don't have to worry about that with these enclosed racks.
Last edited:
Good to know. That looks like a pretty decent fit. I suspect this would also work with the 39/40mm racks as they are the same width, just shorter in length and height. For a longer term solution, I would probably purchase some high density closed cell foam padding and fit some at both the bottom and the top. (front and back in your pics)
And just to clarify to any n00bs reading this, the comment about needing 12 cans of plasti dip was a pretty extreme exaggeration. I plasti dipped both levels of foam on all sides in my 3800 with two cans. Couple spots are a bit thin, but 3 cans max will easily do it.
Last edited:
Two cans was more than enough for all the layers of my 4800. I found that when I sprayed it from a closer range and soaked the foam it seemed to need a lot less coats. It would get pretty rubbery after drying.
tidekg
Sitting Out
I’ll take 10 40mm racks please.
You said those fit the 39mm card molds right?
Thanks
You said those fit the 39mm card molds right?
Thanks
Ordering is closed for this group buy. Racks have already shipped from the vendor.
OP
OP
Will do another soon
eightyWon
Straight
El Máquina
OP
OP
Colquhoun
4 of a Kind
Oh wait, I’m not in this one. 
Keeping track of my purchases is getting ugly.
Keeping track of my purchases is getting ugly.
Johnblue
Flush
LFG!!!! I ordered a FTON of these.
OP
OP
Looks like it will be Monday for delivery
OP
OP
The icy weather from last week slowed these down. Looks like I will be getting about half of them tomorrow. Hopefully the rest will come the next day
OP
OP
10 of the 12 boxes arrived yesterday. Other 2 scheduled for today. Will start sending tracking notices soon.
ric878
High Hand
Just got mine today. These racks are great! Thanks, @justincarothers.
ninedeuce
Two Pair
OP
OP
I will start a new one next week
Mandos
3 of a Kind
I need to get some of these to fit 43MM cards mold. Funny how 1 GB feeds another lol
- Status
Similar threads
