3D3P rack spacers / vendor no longer onsite? (1 Viewer)

[Newenne]

Is this Vendor no more onsite? @One Eyed Dollar

EDIT: to be clear I have no issue with waiting time. Have ordered before and got my stuff after a wait. This post is about whether we know this vendor is still active. Based on vendor page being gonezo. Will of course try to reach out here and via pm

 

[doublebooyah85]

He checks in every 2-3 months and fills orders every 4-6 months fyi.

 

[Newenne]

He checks in every 2-3 months and fills orders every 4-6 months fyi.

I can't find the vendor page or order thread anymore

 

[BarrieJ3]

I think the question is more around that the vendor page no longer exists on site.

It was removed without any notation.

That being said, One Eyed Dollar does always return when possible and provide updates/shipping. Just know that it might be a quick minute as he’s busy with life, but he’ll be back.

I’d imagine you can personally PM him with potential order and he can place you in line when possible.

 

[HaRDHouSeiNC]

I ordered a flattening jig and got it in under a month
He seems to fill orders as he can on his website but be patient.

 

[doublebooyah85]

I think the question is more around that the vendor page no longer exists on site.

It was removed without any notation.

That being said, One Eyed Dollar does always return when possible and provide updates/shipping. Just know that it might be a quick minute as he’s busy with life, but he’ll be back.

I’d imagine you can personally PM him with potential order and he can place you in line when possible.

Several threads also appearing missing that discussed the delay in shipments but they were always fulfilled.

 

[Newenne]

Yup just noticed vendor page down so wondering if he is still actively printing. I notice the webpage is up but still wondering

 

[HaRDHouSeiNC]

Yup just noticed vendor page down so wondering if he is still actively printing. I notice the webpage is up but still wondering

You can message him on his website

He did reply to me after a week or so

Whole order was like $25 so I wasn’t super concerned

 

[Tonysquander]

I think I saw him post at some point that he was not going to renew his vendor status because he wasn’t able to respond as quickly as he felt an official vendor should. He always comes through with the orders eventually though.

 

[Tommy]

I think I saw him post at some point that he was not going to renew his vendor status because he wasn’t able to respond as quickly as he felt an official vendor should. He always comes through with the orders eventually though.

^^^ This

 

[Newenne]

I think I saw him post at some point that he was not going to renew his vendor status because he wasn’t able to respond as quickly as he felt an official vendor should. He always comes through with the orders eventually though.

Aha! Thank you.

 

[Machine]

You ain't ore'n alone, I got an order in early this month too. it'll come in just when you forget about it =)

 

[Goldfish]

FYI, I ordered something back in November and never received it. No response to PMs or emails.

 

[Tommy]

FYI, I ordered something back in November and never received it. No response to PMs or emails.

Send @timinater a PM (or bump it) of you haven't already. He told me was going to take care of remaining orders ASAP.

 

[TheOffalo]

Send @timinater a PM (or bump it) of you haven't already. He told me was going to take care of remaining orders ASAP.

You mean @One Eyed Dollar?

 

[joeyshin]

I’ve ordered twice last year and expected few months before receiving but got my orders within the month. Very pleased and surprised at the turn around time. I just ordered through the website.

 

[Tommy]

You mean @One Eyed Dollar?

Ha, yeah!

 

[calfdemon]

I also ordered from @One Eyed Dollar using his website a couple months ago and noticed that when Google Pay was used, it populated an old shipping address. I immediately messaged him both here and several times on his website with no reply and no way to correct the shipping address. I had pretty much given up hope on receiving anything due to his lack of response, but I will keep my fingers crossed.

I'm afraid that even if he does finally print and ship, it won't be sent to the correct address.

 

[Tommy]

Hmm. I sent him an email with a link to this thread.

 

[doublebooyah85]

His stuff is the best. Love the 10-20 chips stack holders. Hope he stays with it!

 

[timinater]

Send @timinater a PM (or bump it) of you haven't already. He told me was going to take care of remaining orders ASAP.

Ha, yeah!

I’ve been punked!

I hope all the orders get resolved but unfortunately I can’t help with any of this.

 

[Chile85]

@One Eyed Dollar Sending you a PM regarding your printing. I have a friend with a Prusa print farm. If you think a one time catch up on printing would help you sustain as a vendor, I bet he would be willing to help! My prusa is currently employed in his print operation locally

 

[Chile85]

Picture for attention. I believe he has paired down some of the printers during the pandemic... but you get the idea

 

[UniLover]

Ordered 01-28, just got shipping notice yesterday!

 

[Goldfish]

It’s unbelievable that out of all the transactions I have done on this forum, that it is this one that falls into a black hole. Order placed on 11-25, nothing.

 

[doublebooyah85]

It’s unbelievable that out of all the transactions I have done on this forum, that it is this one that falls into a black hole. Order placed on 11-25, nothing.

Haha actually sounds pretty believable lol I feel your pain tho his stuff is perfect and unique

 

[doublebooyah85]

His website no longer offers purchasing either.

As silly as it sounds did he offer a 5 chip holder? I’m not sure I’ll be able to land 10 of these easily and affordable

 

[Newenne]

His website no longer offers purchasing either.

View attachment 1119430

As silly as it sounds did he offer a 5 chip holder? I’m not sure I’ll be able to land 10 of these easily and affordable

Only saw the 10 holders and they are already quite thin. Can't imagine one for 5 (one finger width)

 

[doublebooyah85]

Only saw the 10 holders and they are already quite thin. Can't imagine one for 5 (one finger width)View attachment 1119433

Yeah agree. Probably not.

Love them!

 

[Newenne]

it's too bad he never got efficient / had the time to produce properly. some of those things were da bomb. Glad I picked up those rack stackers when I had the chance